Wear Analysis and Corrective Maintenance Worm Screw Press at PT. XYZ

Muhammad  Ihsan Hamdy; Rika Taslim; Nyvia  Andhen Sury

doi:10.24036/ijimce.v1i1.18

Authors

Muhammad Ihsan Hamdy Departement of Industrial Enginering, Faculty of Science and Technology, State Islamic University of The Sultan Syarif Kasim Riau, INDONESIA
Rika Taslim Departement of Industrial Enginering, Faculty of Science and Technology, State Islamic University of The Sultan Syarif Kasim Riau, INDONESIA
Nyvia Andhen Sury Departement of Industrial Enginering, Faculty of Science and Technology, State Islamic University of The Sultan Syarif Kasim Riau, INDONESIA

DOI:

https://doi.org/10.24036/ijimce.v1i1.18

Keywords:

Corrective maintenance, wear and tear, worm screw press

Abstract

PT. XYZ is one of the palm oil processing companies located in the Riau area. The purpose of this study was to determine the right type of machine maintenance, especially for the worm screw press, because this part often experiences wear and tear which affects the results of pressing palm oil into oil. Wear and tear can partially reduce the surface of the machine and affect the performance of each machine. The service life of the worm screw press provided by the manufacturer is 1000 hours. However, usage at the Sebanga Multi Sawit factory reaches 1300-1500 hours. This proves that there is a need for further studies on good maintenance methods on screw press machines. The calculation of the wear rate and the depth of wear is used to determine the amount of wear that occurs. Solutions that can be done are welding, pack carburizing, and flame hardening on the worm screw press.

Downloads

Download data is not yet available.

References

Suandi A, Supardi NI, and Puspawan A, “Analysis of Palm Oil Processing With Processing Capacity Of 30 Tons/Hour At PT. Bio Nusantara Technology”, TeknosiA, vol. 2, no. 17, pp. 12-19, 2016. [Online]. Avaible: http://repository.unib.ac.id/11706/. [Accessed Sept. 2017]

Nursubiyantoro E, Puryani, and Rozaq M, “Implementation Of Total Productive Maintenance (TPM) In The Implementation Of Overall Equipment Effectiveness (OEE)”, Journal Of Automation System And Industry, vol. 9, no. 1, pp. 24-32, 2016. [Online]. Avaible: https://doi.org/10.31315/opsi.v9i01.2169. [Accessed June. 2016]

Sitepu T, “Analysis of The Age of Use Of Screw Press In Palm Oil Crude Oil Extraction Machine”, Dynamic Journal, vol. 1, no. 7, pp. 1-9, 2010. [Online]. Avaible: https://jurnal.usu.ac.id/index.php/jddtm/article/view/61/30. [Accessed June. 2010]

Mangoensoekarjo, Soepadiyo and Haryono S, Palm Oil Agribusiness Management. Yogyakarta: Gadjah Mada University Press, 2003, pp. 365

Nadapadap RN, Corrective Maintenance Worm Screw Press With A Processing Capacity Of 10 Tons Of Palm Fruits / Hour Using Failure Analysis. Medan: Universitas Sumatera Utara, 2010

Norton RL, Mechanical Design: An Integrated Approach 3rd ed. Pearson Prentice Hall: New Jersey, 2006

Leni, D., Bahar, Z., & Selviyanty, V. (2018). Rancang bangun mesin perajang pelepah sawit untuk pakan ternak. Jurnal Teknik Mesin, 11(2), 51-57.

Prasetyo S, Syawaldi, and Yulianto D, “Failure Analysis And Repair On Worm Screw Press Palm Oil Processing With Geometric Modeling Simulation Method Using Autodesk”, Journal Renewable Energy & Mechanics, vol. 1, no. 2, pp. 40-47, 2018. [Online]. Avaible: https://doi.org/10.25299/rem.2018.vol1.no02.1110. [Accessed Sept. 2018]

Permana TS,Gumilar and Rumendi, St 37 Material Wear Test Analysis Results Of Carburizing And Hardening Using Horizontal Wear Testing Machine, Bandung: STEMAN, 2014, pp. 5

Pribadi B Suprapto dan Dwi P, St40 Steel Surface Hardening By Carburizing Plasma Discharge Method, Yogyakarta: BATAN, 2008, PP. 231-236.